banner



How To Change Battery In Window Alarm Sensor

Past installing a wireless home security system in your home in Charleston, the time may come up eventually that you lot'll accept to replace a battery in one of your wireless window/door sensors. The expert news: information technology'south piece of cake to replace and by doing it yourself, you can save a scrap of coin.

The batteries used in your door sensors can concluding for years later on installation depending on use, merely similar all batteries there is a set lifetime and will take to be replaced.

Most companies volition accuse yous a service fee if they have to send a field security system technician to your dwelling, and so by following these quick, simple steps yous tin can avoid that charge all together.

Note: This guide is for use for Honeywell 5816 Door/Window Transmitters. Not sure what model your sensor is? Give us a call: (843) 789-9994.

1. Determine Which Sensor Has A Low Battery

When a wireless sensor in your abode security system has a depression battery, your keypad will display a "lo bat" message, followed by a number that will tell you lot which zone has a depression battery. The "zone number" corresponds to the area of you lot home that sensor is protecting. If you're non sure almost zone list, you can always give the states a phone call or check the security app, if yous are using 1.

2. Put Your Alert Organization in Examination Mode

At your keypad, enter your user code (the 4 digit code yous apply to arm/disarm your alarm) + the number 5. You lot'll note on most keypads you'll encounter the word "Test" on the number 5.

Putting your alarm in Exam mode prevents any tamper signals sent by your sensor while you are replacing your battery. The tamper signal prevents unauthorized people from tampering/removing/damaging your sensors with the result of that zone condign a vulnerability within your security arrangement.

Placing your alarm in Test mode lets the organization know that y'all are testing or performing maintenance on the arrangement then signals won't exist sent to your warning monitoring visitor.

iii. Take The Cover Off Of Your Sensor

On the bottom of your sensor, yous'll notice a very narrow "slit" or opening. This opening allows yous to carefully insert a small screwdriver to pry off the cover of your sensor. Insert your modest screwdriver and with a simple twist, the cover volition pop off.

The comprehend isn't connected to the mountain of your sensor so information technology will be a solid, split piece that you can set up aside until yous're ready to replace it.

iv. Remove The Sometime Battery & Insert New Battery

Using your modest screwdriver, carefully remove the existing battery. Go on note of the polarity (the "+" and "-" ends of the battery) and put your new bombardment in using the same polarity orientation.

5. Replace Encompass

Now that the new battery is in place, y'all tin can now supervene upon the comprehend you removed earlier. You lot should hear a "snap" as it closes, letting yous know that the cover is securely back on the sensor.

6. Activate The Transmitter

To actuate your transmitter, open and shut your door or window a few times until you hear your keypad beep 3 times each time you open your door or window. If your keypad is too far away for yous to hear, or is in another room, recruit someone to stand up almost your keypad so they can let yous know if the keypad beeps.

7. Take Your Alarm Off of Exam Fashion

Afterwards yous've got your sensor activated, accept your alarm off of Test mode by entering your user code plus the number 1. You'll note that the number 1 has the word "OFF" on it. Enter your 4 digit user code once again, and over again printing the number one. Now, yous should no longer see the "LO BAT" indicate on your keypad.

Additional Notes:

The battery you should use is a CR123A 3V Lithium Battery that you tin can selection up at Batteries Plus in Charleston.

Charleston Security Systems

Charleston Security Systems

Charleston Security Systems provides complete home and business organisation security solutions including domicile security systems, access control systems, alarm monitoring services and video surveillance systems. Our security staff provides the highest level of personalized, affordable services in the industry.

Source: https://charlestonsecuritysystems.net/security-tips/how-to-replace-the-battery-in-your-wireless-windowdoor-sensor/

Posted by: tauntonbutial.blogspot.com

0 Response to "How To Change Battery In Window Alarm Sensor"

Post a Comment

Iklan Atas Artikel

Iklan Tengah Artikel 1

Iklan Tengah Artikel 2

Iklan Bawah Artikel