banner



How To Cut Metal Siding For Window

Download Article

Download Article

Vertical metal siding can give a edifice a modern, sleek appearance. While installing vertical metal siding is similar to installing horizontal siding, in that location are a few differences you'll want to proceed in mind. Fortunately, with the right tools and preparation, putting vertical metal siding up on a building tin be a smooth and simple process.

  1. 1

    Audit the surface y'all're working on to encounter if it's level. Metal siding looks best when it's installed on a apartment, level surface. If the surface yous're working on is uneven, the metallic siding volition look wavy and distorted. Check the wall beforehand so you know whether or not yous'll need to level it out before y'all get started.[1]

    • Employ a level to see if the surface is fifty-fifty and feel for any noticeable dips or bumps in the wall with your hands.
  2. 2

    Install horizontal furring strips every 16 inches (41 cm) if the wall is uneven. Furring strips are thin, wooden strips that you tin find at your local hardware shop. Putting up furring strips will help even out the surface you're working on so the metal siding doesn't look wavy.

    • To install the furring strips, kickoff by cut them to size so they run from 1 end of the surface to the other. Then, blast them to the surface you're working on, leaving 16 inches (41 cm) between each strip.
    • Make sure y'all install the furring strips horizontally and not vertically. They need to run in the reverse direction of the metal siding.

    Ad

  3. 3

    Apply capsule over the wall if you installed furring strips. Installing a layer of sheathing, like plywood, over the furring strips will give y'all an even, insulated surface to work on. Simply cut the material to size and nail it to the furring strips so the entire surface is covered.[2]

    • Choose sheathing that's no more than 1 inch (ii.5 cm) thick and then you lot're not building too far out from the wall.
    • You can find capsule at your local home comeback centre.
  4. 4

    Skip furring strips and capsule if you're working with an fifty-fifty surface. Sometimes it's not necessary to even out the surface you lot're working on, peculiarly if you're installing siding over a relatively new building. If that's the example, yous can put the metallic siding upwardly on the wall as is.[iii]

  5. Advertizement

  1. ane

    Install the corner posts that came with your metallic siding first. The corner posts are the pieces of siding that volition wrap around the corners of the surface you lot're working on. The verbal installation process may vary depending on the siding you lot're using, but generally you volition demand to position the posts on the corners and and so nail them into identify using the cut-out nail slots.[iv]

    • Hammer in a nail about every 12 inches (thirty cm) down both sides of the corner posts.[5]
  2. 2

    Smash j-channel forth the lesser of the wall you're working on. J-channel is an accessory to the siding that's used to receive and hide the ends of the panels and then the concluding product has a smoothen and finished appearance. Employ the smash slots on the j-channel to secure it to the wall, just like you did with the corner posts.[6]

    • You'll need to measure and cut the j-aqueduct to size then it fits along the bottom edge of the surface y'all're working on. Exit a ane4 inch (0.64 cm) gap between each end of the j-channel and the corner posts so it has room to aggrandize and contract.[7]
    • You tin can cut j-aqueduct using tin snips or a power saw.
  3. iii

    Install j-aqueduct along the top edge of the wall. The j-channel at the top of the surface you're working on volition receive 1 stop of the siding panels, while the j-channel at the bottom will receive the other stop. Boom j-channel along the elevation of the wall just like you did with the j-channel at the lesser, except this time the nail slots should be facing downwards.[8]

    • Leave a 1four inch (0.64 cm) gap at each end similar you did with the other j-channel.[9]
  4. 4

    Secure j-channel around the edges of whatever windows and doors. If there are whatsoever windows or doors on the surface you're working on, some of the metal siding will need to be secured to the edges of them. Therefore, at that place needs to be something there to receive and conceal the ends of the siding, which is where the j-aqueduct comes in. Install the j-channel like you lot did forth the top and bottom of the wall, with the bottom edge of the j-channel pushed up against the edge of the windows or doors.[10]

    • There needs to exist j-channel along each edge of the frame around any windows or doors.
    • If your windows or doors already accept a built-in receiver for siding, you don't demand to install j-aqueduct around them.
  5. Advertisement

  1. 1

    Measure the length of the wall to come across how many panels you'll need to use. Depending on the length of the wall, yous may need to cutting and use partial panels. For example, if the wall is xi feet (three.4 thousand) long, and each siding panel is 2 feet (0.61 m) long, you would need 5 panels and 1 half-size panel.[11]

    • Measure the wall earlier you start installing the panels so yous know exactly how many panels and partial panels you need to apply.
    • Siding panels come in dissimilar sizes depending on the brand and blazon that you buy, so brand sure you mensurate your panels before you lot go started.
    • If yous need to cut your panels to size, yous can apply tin snips or a ability saw.
  2. two

    Distribute partial panels evenly on both sides of the wall for a balanced terminate. To proceed your vertical metal siding looking polished and balanced, yous desire to avoid installing a fractional console on just one side of the wall. Instead, you should cut two partial panels that are each half the length of the partial panel you demand and install them on each end of the wall.[12]

    • For example, if y'all demand to apply a partial panel that's 1 foot (0.30 m) long for your installation, you would cut two 6 in (15 cm) panels that would keep the ends of the wall.
    • If you cut fractional panels, punch tabs every half-dozen inches (fifteen cm) along the cut edge to use equally nail slots.
    • If yous don't need to use fractional panels for your installation, you can skip this pace.
  3. 3

    Nail furring and utility channels forth the corners if y'all're using partial panels. Since you'll exist cutting off the edges that are supposed to snap into the corner posts when y'all make partial panels, you'll need to install a vertical furring strip and utility channel next to the corner posts so the partial panels have something to lock into. First, nail the vertical furring strip to the sheathing and so it runs along the edge of the corner post. Then, insert a strip of utility aqueduct into the edge of the corner mail service and boom it into identify using the nail slots.[thirteen]

    • If you're non using fractional panels for your installation, there'due south no demand to install furring strips or utility channels.
  4. 4

    Install the outset console by snapping it into the receiver on the corner post. Line the edge of the panel that doesn't take the smash slots up with the edge of the corner mail and and so slide it into place. You should hear it click as it locks into place.[fourteen]

    • If you lot're using a fractional panel, slide the cut edge of the panel into the utility channel y'all installed until it locks into place.
    • Make sure the pinnacle and lesser ends of the panel are locked into the j-channel you installed along the top and bottom of the wall before.
  5. 5

    Hammer nails into the nail slots every 16 inches (41 cm) downwards the panel. Once i edge of the panel is locked into place, you lot'll need to nail the other edge to the sheathing to secure the panel.[15]

    • Make sure you hammer a nail into the top and bottom smash slots on the console.
  6. 6

    Install the second console so it overlaps with the first panel. Start, snap the edge of the second panel into the receiving groove on the beginning console so it locks into place. The second console should cover the nails that y'all used to secure the commencement panel to the sheathing. Then, boom the 2nd panel to the sheathing only like you lot did with the first console.[16]

  7. 7

    Repeat with the residuum of the siding panels. Continue to lock and nail the panels into place until you attain the other side of the wall. If you're using partial panels, install the second fractional panel when you accomplish the other corner post.

    • If the surface y'all're working on doesn't accept whatsoever windows or doors that you need to work around, y'all're finished!
  8. 8

    Cutting panels to fit around any windows and doors on the wall. If you need to panel around whatsoever windows or doors, start by belongings the panel over the section of the window or door you're working with. Then, measure and marker where you need to cut out infinite for the frame on the panel. Cut out that department of the panel and then snap the cutting edge of the panel into place using the j-aqueduct you installed effectually the window or door earlier.[17]

    • Once the panel is locked into the j-channel, boom the panel to the sheathing using the nail slots that are above and below the window or door.
  9. Advertizing

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Advertisement

Things You'll Need

  • Furring strips and sheathing (if you're working on an uneven surface)
  • Hammer
  • Nails
  • Metal siding
  • J-channel
  • Tin snips or power saw
  • Measuring tape
  • Level

Virtually This Commodity

Article Summary X

To install vertical metal siding, beginning by applying horizontal furring strips and sheathing to the surface you lot're working on if information technology's uneven. Then, install the corner posts that came with your siding and nail j-channel along the summit and bottom of the wall. If at that place are any windows or doors, boom j-channel around the edges of those too. Adjacent, install the siding one console at a fourth dimension by snapping it onto the panel before it and nailing it to the sheathing. To learn how to measure and cut the siding panels for your project, read on!

Did this summary assist you?

Thanks to all authors for creating a page that has been read 62,165 times.

Did this article aid you?

Source: https://www.wikihow.com/Install-Vertical-Metal-Siding

Posted by: tauntonbutial.blogspot.com

0 Response to "How To Cut Metal Siding For Window"

Post a Comment

Iklan Atas Artikel

Iklan Tengah Artikel 1

Iklan Tengah Artikel 2

Iklan Bawah Artikel